ShopwoodPlans

1/4" cordless impact drivers · Comparison

Milwaukee vs DeWalt impact driver (2026): M18 FUEL 2953-20 vs DCF845B

The short answer

More torque, self-tapping screw mode? Milwaukee

Already on DeWalt 20V batteries? DeWalt

Both are brushless 1/4 in. hex impact drivers sold as bare tools, each with a low-speed mode for small screws. Milwaukee lists more torque (2,000 vs 1,825 in-lbs) and a higher top speed (3,900 vs 3,400 rpm), plus a mode for self-tapping screws in sheet metal. DeWalt’s low mode is Precision Drive, which it names for cabinet hinge screws and machine screws.

Best for torque and speed

Pick the Milwaukee M18 FUEL 2953-20 if

  • You want the most torque here: Milwaukee lists 2,000 in-lbs.
  • You drive self-tapping screws into sheet metal. It has a mode for #8 to #12 screws in 18 to 22 gauge.
  • You want the longer warranty: 5 years vs 3.

Tool only 2953-20: impact driver and belt clip. No battery or charger.

Check the Milwaukee impact driver on Amazon

Best for DeWalt 20V owners

DeWalt DCF845 20V MAX XR 3-speed impact driver, side view, shown with battery
Image: DeWalt. Shown with a battery, which is sold separately.

Pick the DeWalt DCF845B if

Full DeWalt DCF845 review

  • You already own DeWalt 20V MAX batteries.
  • You set a lot of small screws. Precision Drive hesitates as the screw head reaches the work, then impacts slowly if needed.
  • You want tool tracking. It’s ready for a DeWalt Tool Connect chip (sold separately).

Tool only DCF845B: impact driver and belt hook. No battery or charger.

Check the DeWalt impact driver on Amazon

Before you buy: I compared the two bare tools (no battery or charger). When I checked on Oct 9, 2026, the Milwaukee listing was sold by a third-party seller and the DeWalt listing by Amazon. Milwaukee’s warranty covers tools bought from an authorized Milwaukee distributor. Listings change, so check who the seller is and that it’s new before you order.

As an Amazon Associate I earn from qualifying purchases.

Key specs

3Milwaukee 2953-20
spec rows won
1DeWalt DCF845B
spec rows won
6even or
unclear

This counts the rows below where one is clearly better. It’s a tally, not an overall rating. Both have a gentle low-speed mode, so the tally comes down to power, warranty and tool tracking.

A green check means that number or feature is clearly better. No check means it's a tie, the gap is tiny, or the makers measure it differently. Every figure comes from Milwaukee or DeWalt, not from Amazon.

Milwaukee 2953-20DeWalt DCF845B
Max torque2,000 in-lbs1,825 in-lbs
Top speed3,900 rpm3,400 rpm
Impact rateUp to 4,400 ipmNot published
Drive modes4: three speeds plus a self-tapping screw mode3: Precision Drive, normal, high speed
Low-speed mode0–1,700 rpm0–1,500 rpm (Precision Drive)
Chuck1/4 in. hex quick change one-handed bit insertion1/4 in. hex quick release takes 1 in. bit tips
Work lightTri-LED3-LED
Weight as listed2.2 lb without battery2.35 lb assembled product weight
Tool trackingNot ONE-KEY enabledTool Connect chip-ready chip sold separately
Tool warranty5 years3 years plus 1 year free service
Spec notes
  • Weight: Milwaukee lists 2.2 lb without a battery. DeWalt’s page lists 2.35 lb as an assembled product weight, which may be measured differently, so the row isn’t scored.
  • Length: Milwaukee lists a 4.47 in. head length. DeWalt’s page only lists an 8.07 in. assembled product length, so the two can’t be compared and length is left out.
  • Impact rate: Milwaukee’s manual lists up to 4,400 impacts per minute. I couldn’t find an impact rate on DeWalt’s DCF845B page or manuals, so the row isn’t scored.
  • Speeds: Milwaukee’s manual lists 0–1,700, 0–3,000 and 0–3,900 rpm for its three speeds. DeWalt’s manual lists 0–1,500, 0–2,800 and 0–3,400 rpm.

What it can handle

These are common impact-driver jobs, checked against each maker’s own modes, ratings and manuals. I haven’t tested either driver. If a job needs something the maker doesn’t support, it gets a CAN’T.

JobMilwaukee 2953-20DeWalt DCF845B
Screws
Cabinet hinges Can doMode 1 (up to 1,700 rpm) for small fasteners. Can doPrecision Drive; DeWalt names cabinet hinge screws.
Self-tapping screws Can doDedicated mode for #8–#12 screws in 18–22 ga sheet metal. Can doRated for impact screwdriving; no self-tapping mode listed.
Large screws Can do2,000 in-lbs max torque. Can doDeWalt pitches it for large-diameter screws; 1,825 in-lbs.
Bits
Hex-shank drill bits Can doTakes 1/4 in. hex accessories. Can doTakes 1/4 in. hex accessories.
Round-shank bits Can’t1/4 in. hex drive only. Can’t1/4 in. hex accessories and 1 in. bit tips only.
Limits
Exact torque Can’tNot a torque wrench; Milwaukee says check with a hand torque wrench. Can’tNot a torque wrench; DeWalt says check with one.
Low light Can doTri-LED light. Can do3-LED work light.

Torque figures are the makers’ maximums. Fastener size, wood species and battery charge all change how a screw drives.

Notes and sources

How the verdicts were made: modes and speeds come from each operator’s manual; torque and features come from the product pages. Nothing here comes from hands-on testing or owner reviews.

Self-tapping screws: Milwaukee’s manual describes a mode made for #8, #10 and #12 self-tapping screws, 1/2–1 in. long, in 18–22 gauge sheet metal. DeWalt doesn’t list a matching mode, but nothing in its manual rules the job out, so both get CAN DO.

Exact torque: both manuals say an impact tool isn’t a torque wrench, so jobs with a specified torque get CAN’T for both.

Sources:

Battery platform: what else runs on it

These are bare tools, so your batteries decide a lot. The packs don’t cross over between brands.

Milwaukee M18

Milwaukee says the 2953-20 works with all M18 batteries and chargers.

DeWalt 20V MAX

The DCF845B is part of DeWalt’s 20V MAX XR line. DeWalt says the 20V MAX line has more than 300 products.

Who should buy which

Get the Milwaukee M18 FUEL 2953-20 if:

  • You want the most torque and speed of the two.
  • You drive self-tapping screws into sheet metal or metal studs.
  • You’re on M18 batteries, or you want the 5-year warranty.
Check the Milwaukee impact driver on Amazon

Get the DeWalt DCF845B if:

  • You already own DeWalt 20V MAX batteries.
  • You set a lot of hinge screws and small hardware.
  • You want to add Tool Connect tracking later.
Check the DeWalt impact driver on Amazon

As an Amazon Associate I earn from qualifying purchases.

Skip it if

Skip the Milwaukee 2953-20

if you’re already on DeWalt 20V batteries. Both drivers have a low-speed mode for small screws.

Skip the DeWalt DCF845B

if you want the most torque, a self-tapping screw mode, or the longer warranty.

Questions about this pair

Which impact driver is more powerful?

On the makers’ specs, the Milwaukee: 2,000 in-lbs and 3,900 rpm, vs 1,825 in-lbs and 3,400 rpm for the DeWalt.

Is an impact driver good for cabinet hinges?

Both have a low-speed mode for small screws. DeWalt names cabinet hinge screws for its Precision Drive mode. Milwaukee’s mode 1 tops out at 1,700 rpm.

Can I use regular drill bits?

Only hex-shank bits. Both take 1/4 in. hex accessories, not round shanks.

Do they come with a battery?

No. Both listings here are tool only.

Spec notes
  • Amazon listings compared: Milwaukee 2953-20 tool only (B0BB8H1NKX) and DeWalt DCF845B tool only (B0BQCWH5KF). Both are bare tools, so this is tool against tool.
  • Why the DCF845B and not the older DCF887B: the DCF887B no longer has a page on DeWalt’s US site, so its specs couldn’t be checked against the maker. The DCF845B is DeWalt’s current 20V MAX XR 3-speed 1/4 in. impact driver.

Specs checked October 9, 2026 against Milwaukee's and DeWalt's own pages and manuals. Links are in "Notes and sources" under the chart above.

By Mike E. · Last checked October 9, 2026 · Based on manufacturer specs. Not tested hands-on.