ShopwoodPlans

10" dual-bevel sliding miter saws · Comparison

Bosch CM10GD vs Makita LS1019L miter saw (2026): 10" dual-bevel sliders

The short answer

Taller crosscuts, vacuum adapter included? Bosch

Laser, 60° both ways, lighter? Makita

Both are corded 15 A, 10 in. dual-bevel sliding miter saws that crosscut 12 in. at 90°. They slide differently: the Bosch uses its Axial-Glide arm, and the Makita uses two steel rails that Makita says let it work flush against a wall. Both list an electric brake. The Bosch cuts taller stock at 90° (3-1/8 in. vs 2-13/16 in.). The Makita has a laser and soft start, miters to 60° both ways, cuts deeper at a 45° bevel, and weighs about 6 lb less.

Best for taller cuts

Pick the Bosch CM10GD if

  • You cut taller stock. It crosscuts 3-1/8 in. high by 12 in. wide at 90°.
  • You’re short on space behind the saw. Bosch says the Axial-Glide arm takes up to 10 in. less front-to-back space than a slide miter saw.
  • You want a vacuum adapter in the box. Bosch includes one with the dust bag.

CM10GD box: saw, 60-tooth blade, wrench, work clamp, dust bag, vacuum adapter/elbow. No stand.

Check the Bosch saw on Amazon

Best for trim and angles

Pick the Makita LS1019L if

  • You want a laser cut line. It shifts to either side of the blade.
  • You miter past 52° on the left. It miters to 60° both ways.
  • You want the lighter saw: 57.9 lb vs 64 lb.

LS1019L box: saw, 60-tooth blade, vertical vise, dust bag, triangular rule, hex wrench. No stand.

Check the Makita saw on Amazon

Before you buy: I compared the two saws on their own, without a stand. When I checked on Oct 9, 2026, both were sold by Amazon, and the Bosch showed a delivery wait of about two weeks. Listings change, so check who the seller is, that it’s new, and the delivery estimate before you order.

As an Amazon Associate I earn from qualifying purchases.

Key specs

1Bosch CM10GD
spec rows won
5Makita LS1019L
spec rows won
6even or
unclear

This counts the rows below where one is clearly better. It’s a tally, not an overall rating. The Bosch’s main selling point, the space-saving Axial-Glide arm, isn’t a number either maker publishes the same way, so it isn’t scored.

A green check means that number or feature is clearly better. No check means it's a tie, the gap is tiny, or the makers measure it differently. Every figure comes from Bosch or Makita, not from Amazon.

Bosch CM10GDMakita LS1019L
Motor15 A, 5,000 rpm15 A, 3,200 rpm
SlideAxial-Glide armTwin steel rails
Crosscut at 90°3-1/8 in. x 12 in.2-13/16 in. x 12 in.
Crosscut at 45° miter3-1/8 in. x 8 in.2-13/16 in. x 8-1/2 in.
Depth at 45° bevel (L / R)1-1/2 in. / 1 in.1-7/8 in. / 1-1/8 in.
Miter range52° left, 60° right60° left and right
Bevel range47° left and right48° left and right
Crown, nested (45° type)6 in.6-5/8 in. with crown stopper, sold separately
LaserNoneYes, shifts left or right of blade
Electric brakeYesYes
Soft startNot listedYes
Net weight64 lb57.9 lb
Spec notes
  • Footprint: Bosch lists a 30 in. front-to-back depth and says the Axial-Glide arm takes up to 10 in. less front-to-back workspace than a slide miter saw. Makita says its rail design lets the saw work flush against a wall. The two claims can’t be compared directly, so footprint isn’t scored.
  • Crown: Makita’s 6-5/8 in. figure is with its crown molding stopper, which is sold separately. Bosch lists 6 in. nested against the fence for 45° spring crown. Because one figure needs an extra part, the row isn’t scored.
  • Baseboard: left out. Bosch’s spec page lists 3-1/4 in. against the fence, while Makita lists 5-1/4 in. with its horizontal vise (sold separately). The two figures are measured differently.
  • Warranty: Bosch covers corded tools for 1 year. I couldn’t confirm Makita’s term from a Makita page, so the row is left out.

What it can handle

These are common miter-saw cuts, checked against each maker’s published capacities. I haven’t tested either saw. If a cut is past a published capacity, it gets a CAN’T.

CutBosch CM10GDMakita LS1019L
Crosscuts
2x12 at 90° Can do1-1/2 x 11-1/4 in. fits its 3-1/8 x 12 in. Can do1-1/2 x 11-1/4 in. fits its 2-13/16 x 12 in.
2x8 at 45° miter Can do7-1/4 in. fits its 8 in. at 45°. Can do7-1/4 in. fits its 8-1/2 in. at 45°.
2x10 at 45° miter Can’t9-1/4 in. is past its 8 in. at 45°. Can’t9-1/4 in. is past its 8-1/2 in. at 45°.
Bevels
2x, 45° left bevel Just barely1-1/2 in. is exactly its left-bevel max. Can doUnder its 1-7/8 in. left-bevel max.
2x, 45° right bevel Can’tPast its 1 in. right-bevel max. Can’tPast its 1-1/8 in. right-bevel max.
3/4" board, either bevel Can doUnder its 1 in. right and 1-1/2 in. left. Can doUnder its 1-1/8 in. right and 1-7/8 in. left.
Trim and angles
Crown, 6" (nested) Just barelyExactly its 6 in. nested max. Just barelyInside its 6-5/8 in., but needs the crown stopper sold separately.
60° miter, left Can’tLeft miter stops at 52°. Can doMiters to 60° left.
Laser line Can’tNo laser. Can doBuilt-in laser.

Capacities are the makers’ maximums with a 10 in. blade. Clamp the work and let the blade stop before lifting it.

Notes and sources

How the verdicts were made: capacities come from Bosch’s spec page and Makita’s operator’s manual. Nothing here comes from hands-on testing or owner reviews.

Lumber sizes: a 2x is 1-1/2 in. thick, a 2x8 is 7-1/4 in. wide, a 2x10 is 9-1/4 in. wide, and a 2x12 is 11-1/4 in. wide.

Bevel cuts: both saws cut less on a right bevel than a left bevel. The rows give each side its own verdict so they don’t look contradictory.

Sources:

Who should buy which

Get the Bosch CM10GD if:

  • You crosscut taller stock, up to 3-1/8 in.
  • You want a vacuum adapter in the box.
  • You’re short on depth behind the saw and like the Axial-Glide arm.
Check the Bosch saw on Amazon

Get the Makita LS1019L if:

  • You cut a lot of trim, crown and odd angles.
  • You want a laser and 60° miters both ways.
  • You move the saw around and want the lighter one.
Check the Makita saw on Amazon

As an Amazon Associate I earn from qualifying purchases.

Skip it if

Skip the Bosch CM10GD

if you want a laser, 60° left miters, or deeper 45° bevel cuts in 2x stock.

Skip the Makita LS1019L

if you crosscut stock taller than 2-13/16 in. or need the shallower Axial-Glide footprint.

Questions about this pair

Which cuts bigger, the Bosch CM10GD or Makita LS1019L?

Both crosscut 12 in. wide at 90°. The Bosch cuts taller (3-1/8 in. vs 2-13/16 in.). At a 45° bevel the Makita cuts deeper on both sides.

Does either have a laser?

The Makita LS1019L has a built-in laser that can be set to either side of the blade. Bosch doesn’t list one for the CM10GD.

Can they cut crown molding nested?

Bosch lists 6 in. crown nested against the fence (45° spring). Makita lists 6-5/8 in. using its crown molding stopper, sold separately.

Do they come with a stand?

No. Both listings here are the saw only.

Spec notes
  • Amazon listings compared: Bosch CM10GD (B00G5R4E9A) and Makita LS1019L (B073K99HWJ). Both are the saw only, without a stand.

Specs checked October 9, 2026 against Bosch's and Makita's own pages and manuals. Links are in "Notes and sources" under the chart above.

By Mike E. · Last checked October 9, 2026 · Based on manufacturer specs. Not tested hands-on.