The short answer
More torque, more light, shorter package? DCF860B
Already on a 845, or want the lighter assembled label? DCF845B
These are DeWalt’s current 20V MAX XR 3-speed 1/4-in. hex impact drivers, sold as bare tools. The DCF860B is the one DeWalt calls its highest-torque impact driver, at 2,500 in-lbs, with 9 LEDs and a 20-minute work-light setting. The DCF845B is listed at 1,825 in-lbs and a 3-LED light. Both are brushless, chip-ready for TOOL CONNECT (chip sold separately), and carry the same 3-year limited warranty plus 1 year of free service and 90-day satisfaction guarantee.
Best for heavy fasteners

Pick the DCF860B if
- You want the official 2,500 in-lbs max torque (the higher of this pair) and up to 3,800 RPM.
- You want 9 built-in LEDs and a 20-minute work-light setting.
- You drive a lot of self-drilling or tapping screws. DeWalt says speeds 1 and 2 are tuned for those installation speeds (check the manual and the screw maker).
Tool only DCF860B: impact driver and belt hook. Battery, charger, and TOOL CONNECT chip sold separately.
Check the DeWalt DCF860 on AmazonBest if you already own a 845

Pick the DCF845B if
- 1,825 in-lbs and 3,400 RPM cover the work you do, and you already have this tool on the 20V MAX platform.
- You want the 3-LED work light and a 3-speed, variable-trigger driver without stepping up to the 860.
- You prefer the lower official assembled-product weight label (2.35 lb vs 2.8 lb). That label is not a verified bare-tool weight for either model.
Tool only DCF845B: impact driver and belt hook. Battery, charger, and TOOL CONNECT chip sold separately.
Check the DeWalt DCF845 on AmazonBefore you buy: I compared the two bare tools (no battery or charger). DeWalt limits warranty coverage to DeWalt or authorized sellers. Listings change, so check who the seller is and that it’s new before you order.
As an Amazon Associate I earn from qualifying purchases.
Key specs
spec rows won
spec rows won
not scored
This counts the rows below where one is clearly better on an official figure. It is a tally, not an overall rating. Assembled size and weight labels are not scored, because they are not verified bare-tool measurements.
A green check means that number or feature is clearly better. Every figure comes from DeWalt’s US product page or the official DCF860 manual, not from Amazon.
| DCF845B | DCF860B | |
|---|---|---|
| Official max torque | 1,825 in-lbs | 2,500 in-lbs |
| Official top no-load speed | 3,400 RPM | 3,800 RPM |
| Per-mode torque (official manual) | Not listed in the official sources checked today | 2,500 / 2,150 / 1,250 in-lbs (high / medium / low) |
| Per-mode RPM (official manual) | Not listed in the official sources checked today | 0–1,800 / 0–2,500 / 0–3,800 RPM |
| Impact rate | Not listed on the official US page or the DCF845 manual checked today | 0–4,500 IPM (official manual) |
| Speed modes | 3-speed setting + variable trigger | 3-speed mode select; speeds 1–2 tuned for self-drilling and tapping screws |
| Chuck | 1/4 in. hex, quick-release | 1/4 in. quick-connect hex |
| Work light | Integrated 3-LED | 9 LEDs + 20-minute work-light setting |
| Assembled length (product-page label) | 8.07 in. | 5.63 in. not a verified head length |
| Assembled weight (product-page label) | 2.35 lb | 2.8 lb; official manual also lists 2.4 lb (1.1 kg) |
| Tracking | TOOL CONNECT chip-ready; chip sold separately | TOOL CONNECT chip-ready; chip sold separately |
| US warranty | 3-year limited, 1 year free service, 90-day satisfaction | 3-year limited, 1 year free service, 90-day satisfaction |
Spec notes
- DCF845 impact rate and Precision Drive: I could not confirm a 4,200 IPM figure, per-mode RPM, or a “Precision Drive” label on today’s official US product page or in the official DCF845 manual fetched for this check. Those claims are omitted.
- Size and weight: The official pages list assembled-product length and weight. The DCF860 manual adds 2.4 lb (1.1 kg) without calling it a bare-tool weight. I did not score those rows.
- 20V MAX: DeWalt’s usual footnote applies: maximum initial battery voltage measured without a workload is 20 volts; nominal voltage is 18.
What it can handle
These are common impact-driver jobs, checked only against what DeWalt lists on the official pages and in the DCF860 manual. I have not tested either tool. If a job needs something the maker does not list, it gets a CAN’T or stays unscored.
- Can do Inside the maker’s listed limits
- Check the manual Official wording is qualified, or a figure is missing
- Can’t confirm Not something DeWalt lists for that model in the sources used here
| Job | DCF845B | DCF860B |
|---|---|---|
| Fasteners | ||
| Driving large-diameter screws | Can doOfficial page: 1,825 in-lbs and 3,400 RPM “to drive large diameter screws.” | Can doOfficial 2,500 in-lbs max; DeWalt markets it as its highest-torque impact driver. |
| Self-drilling or tapping screws | Check the manual3-speed control is listed; DeWalt does not spell out self-drilling tuning on the 845 page checked today. | Can doSpeeds 1 and 2 are officially optimized for common self-drilling and tapping screws; follow the manual and the screw maker. |
| Torque-critical hardware | Check the manualImpact drivers are not a calibrated torque wrench. Confirm fasteners with a torque wrench when the joint matters. | Check the manualThe official DCF860 manual gives the same warning: use a calibrated torque wrench for specified torques. |
| Low-light work for 20 minutes at a time | Can’t confirmA 3-LED light is listed; a 20-minute light mode is not. | Can doOfficial 9 LEDs and a 20-minute work-light setting. |
Who should buy which
If you already live on DeWalt 20V MAX batteries, either bare tool drops in. The 860 is the one to buy when official torque, top speed, and lighting matter, or when you drive a lot of self-drilling screws. Keep the 845 if you already own it and 1,825 in-lbs is enough. I would not replace a working 845 just to pick up the 3-LED vs 9-LED difference unless you also need the extra torque.
Both are tool-only. Budget for a battery and charger if you are starting the platform, and for a TOOL CONNECT chip only if you actually use DeWalt’s tracking system.
Skip it if
- You need a Milwaukee M18 tool, or you want a 5-year tool warranty. See the Milwaukee vs DeWalt impact-driver pages instead.
- You need a compact Atomic-class driver (DCF850) or an older DCF887. Those are different models.
- You need a published impact rate for the 845. DeWalt does not list one on the official US page checked today.
Questions about this pair
Is the DCF860 just a more powerful DCF845?
On official paper, yes in the ways that matter: 2,500 vs 1,825 in-lbs, 3,800 vs 3,400 RPM, 9 LEDs with a 20-minute mode vs a 3-LED light, and official speed-1/2 tuning for self-drilling screws. Both are 20V MAX XR, 3-speed, 1/4-in. hex, chip-ready bare tools with the same warranty wording.
What do the three speeds do on each tool?
Both have a 3-speed selector and a variable-speed trigger. For the 860, the official manual lists 0–1,800 / 0–2,500 / 0–3,800 RPM and 2,500 / 2,150 / 1,250 in-lbs, and the product page says speeds 1 and 2 are optimized for common self-drilling and tapping screws. For the 845, the official US page lists a 3-speed setting and a 3,400 RPM top figure; I did not confirm per-mode RPM or a named Precision Drive mode in the official sources used today.
How long and how heavy are they?
Official assembled-product labels: 845 is 8.07 in. long and 2.35 lb; 860 is 5.63 in. long and 2.8 lb. Those are not verified head-length or bare-tool weights. The official 860 manual also lists 2.4 lb (1.1 kg).
Do they take the same bits?
Yes, both are 1/4-in. hex quick-release / quick-connect chucks. The 845 manual specifies 1/4 in. (6.35 mm) hex accessories and says to use impact-rated bits only.
Is a battery included?
No. Both official US pages are tool-only. The box is the driver and a belt hook. Battery, charger, and the TOOL CONNECT chip are sold separately.
What is the warranty, and does Amazon count?
DeWalt lists a 3-year limited warranty, 1 year of free service, and a 90-day satisfaction guarantee on both product pages. DeWalt limits coverage to DeWalt or authorized sellers. Check who the Amazon seller is before you order.
Can I use these as a torque wrench?
No. The official 860 manual warns that impact drivers are not for setting specified torques; use a calibrated torque wrench when the joint requires it. The same caution applies to any impact driver, including the 845.
Which ASIN is the current US bare tool?
DCF845B is B0BQCWH5KF and DCF860B is B0D45VX1FG, both live US bare-tool listings as of November 19, 2026. Kit SKUs (P1, P2, WW1, and so on) add batteries and are not this comparison.
Sources
- DeWalt DCF845B US product page: dewalt.com DCF845B (checked Nov 19, 2026).
- DeWalt DCF860B US product page: dewalt.com DCF860B (checked Nov 19, 2026).
- Official DCF860 instruction manual NA180100 (torque by mode, RPM, 0–4,500 IPM, 2.4 lb / 1.1 kg, torque-wrench warning).
- Official DCF845 instruction manual (3-speed 1/4 in. hex driver, trigger worklight, belt hook, 3-year limited warranty terms).
- DeWalt authorized-seller warranty wording already used on the live DCF845 and DCF860 reviews.