ShopwoodPlans

12 in compound miter saws · Single-tool guide

DeWalt DWS716 miter saw

Quick verdict

The DWS716 is a 12 in non-sliding miter saw that bevels 0–48° both ways, so trim and crown work doesn’t mean flipping long boards. Its manual rates it to 7.9 in wide at 0° (2.9 in high). The issue owners raise is squareness, and the manual gives the fence and bevel adjustments to fix it, so check both on day one.

Good fit

Get it if

  • You cut crown, trim and compound angles and want bevels both ways.
  • You want 6-1/2 in base vertical and 6-5/8 in nested crown capacity.
  • You want the dust duct as well as the bag.

Look elsewhere

Skip it if

  • You crosscut boards wider than about 7.9 in.
  • You rarely bevel right.
  • You won’t check square on arrival.

As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.

Usage info: our math

Bevel 0–48° left and right, with stops at 0, 22.5, 33.9 and 45°. Miter 0–50° both ways with 14 positive stops (dewalt.com). Base vertical 6-1/2 in and nested crown 6-5/8 in come from DeWalt’s product page; the manual doesn’t state a nested crown figure.

Manual cut capacities (p6): at 0° miter, 3.6 in high x 7.2 in wide, or 7.9 in wide x 2.9 in high. At 45° miter, 3.6 x 4.9 in, or 5.5 x 2.9 in. At 45° bevel, 2.3 x 7.4 in left and 1.6 x 7.1 in right. Baseboard 0.75 x 6.5 in on a 45° miter.

What that means (our math from the official figures, not a maker claim): a 2x4 or 4x4 (3.5 in) fits under the 3.6 in height at 0° and 45° miter. A 2x8 (7.25 in wide, 1.5 in thick) fits at 0° because it’s within the 7.9 in width at 2.9 in height.

Who it’s for, who should skip

Who it’s for

  • You cut crown, trim and compound angles and want bevels both ways.
  • You want 6-1/2 in base vertical and 6-5/8 in nested crown capacity.
  • You want the dust duct as well as the bag.

Who should skip it

  • You crosscut boards wider than about 7.9 in. That’s the manual’s widest cut at 0°; the sliding DWS780 is rated to 2x14.
  • You rarely bevel right. The DWS715 does square and miter cuts with left bevel.
  • You won’t check square on arrival. Owners report fence and bevel squareness issues.

Honest downsides

What owners don’t like

Owner threads here come from web-search result snippets on Oct 22, 2026; Reddit blocked direct reads, so we didn’t open the threads in full. Small sample: a count means “this many of the threads that search returned”, not a failure rate. We didn’t check Amazon reviews for this tool.

Fence or bevel out of square

Reported in 2 of 2 owner threads on the DWS716 family that our Oct 21, 2026 search returned (Reddit r/Dewalt and r/woodworking; search snippets, small sample)

One owner of the DWS716XPS variant found the fence out of square on several store units; another found the bevel angle changing between the arm up and down. An older DW716 thread wasn’t counted.

Fix: The manual gives the miter scale, 0° bevel stop, 45° stops and fence steps (p7–9, under Maintenance and care below). DeWalt also has miter saw adjustment videos listing the DWS713/715/716. If it won’t hold square, use the 90-day money-back period or a warranty claim.

Avoid or spot it: Check the fence against the blade with a square, and check bevel at 0° with the arm both up and down, before the return window closes.

Warranty and claims

Length: 3-year limited warranty, 1-year free service contract and a 90-day money-back period (dewalt.com warranty page, read Oct 21, 2026). It covers the original end user only.

Who’s covered: DeWalt says the warranty applies only to tools bought from DeWalt or a DeWalt authorized seller, and it may reject claims for tools bought from unauthorized sellers, including unauthorized websites. DeWalt doesn’t name Amazon.com either way. If you’re unsure about a seller, DeWalt says to ask internetadmin@sbdinc.com.

Registration: not required, and nothing on DeWalt’s warranty page says it extends the term.

Not covered: normal wear, abuse, accessories, and repairs someone else attempted.

How to claim: 1) Find your receipt. DeWalt says proof of purchase showing when and where you bought it may be required, and a receipt is required for the 90-day refund. 2) Use DeWalt’s web request form at support.dewalt.com (DeWalt calls it the fastest route), call 1-800-433-9258, or take the tool to a DeWalt service center (dewalt.com/service-center). 3) Don’t open the tool yourself first; repairs by others are excluded.

Maintenance and care

From DeWalt DWS716 manual N748087 (Type 20, checked Oct 22, 2026). Page numbers are PDF pages. Unplug the saw before any adjustment.

Blade change (p7)

Miter square and scale (p7, p9)

Bevel stops (p7–9)

Fence (p8)

Brake

Mounting and dust (p6, p10)

Cleaning and service (p13)

What else you’ll need

Not linked yet: we haven’t verified retail listings for these parts.

12 in crosscut blade

Why: The stock blade dulls; a 60T or 80T blade gives cleaner trim cuts.

Who can skip it: Until the stock blade dulls.

Is it good? Not tallied.

Official or third-party: Either.

Will it fit? Must be 12 in (305 mm), rated at least 4,800 rpm, crosscut type with a hook angle of 7° or less; never a smaller diameter. The manual’s accessory page says to always use 1 in arbor holes, but its blade-change steps (p7) explain mounting a 5/8 in bore blade with the 1 in blade adapter removed. The manual disagrees with itself, so a 1 in arbor blade is the safe buy. Manual tooth table: 40T general, 60T and 80T fine crosscut, 96T non-ferrous (TCG).

No listing: blade part numbers aren’t verified yet.

DW7084 crown molding fence

Why: Holds crown in place for nested cuts.

Who can skip it: If you don’t cut crown.

Is it good? Not tallied.

Official or third-party: Official DeWalt.

Will it fit? Named in the DWS716 manual (p13).

Not linked yet.

DW7090 clamp and DW7053 dust bag

Why: Clamp for small or repeat cuts; replacement bag.

Who can skip it: If you clamp by hand or run a vac.

Is it good? Not tallied.

Official or third-party: Official DeWalt.

Will it fit? Both named in the DWS716 manual (p13).

Not linked yet.

DeWalt stands DWX723, DWX724, DWX725B, DWX726

Why: A miter saw stand gives you a working height and long-board support.

Who can skip it: If the saw sits on a bench with support either side.

Is it good? Not tallied.

Official or third-party: Official DeWalt.

Will it fit? Named in the DWS716 manual (p10, p13).

Amazon listings not confirmed yet.

As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.

Budget and upgrade picks

Is it better than the alternatives?

FAQ

Does it bevel both ways?

Yes, 0–48° left and right.

Is the DWS716XPS the same saw?

It’s a variant; our data doesn’t detail the differences.

What crosscut capacity does the DWS716 have?

At 0° miter, 7.2 in wide at 3.6 in high, or 7.9 in wide at 2.9 in high (manual p6).

What blades fit?

12 in, rated at least 4,800 rpm, crosscut type. The manual says to use 1 in arbor blades but also explains fitting 5/8 in bores with the adapter removed; a 1 in arbor blade is the safe choice.

Does it have a laser?

No. Only the DWS716XPS has the LED CUTLINE light.

Which way does the blade screw turn?

It’s left-hand thread: clockwise loosens.

Which DeWalt accessory numbers fit the DWS716?

The Type 20 manual (N748087) lists the DW7090 clamp, the DW7053 dust bag and the DW7084 crown molding fence.

How much does the DWS716 weigh?

50.35 lb assembled, per DeWalt’s US product page. DeWalt’s Canadian page lists 41 lb, and the manual doesn’t give a weight.

Sources

DeWalt DWS716 12 in double-bevel compound miter saw

As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.

By Mike E. · Updated Nov 3, 2026 · Based on manufacturer specs, manuals and owner reports. Not tested hands-on.