Quick verdict
The DWS780 is DeWalt’s 12 in sliding double-bevel miter saw with the XPS shadow cutline. Get it for wide crosscuts (capacity table below). In the 63 Amazon reviews we counted, owners most often praise accurate, square cuts and most often complain about dust collection and hose fit, then support trouble and the XPS light dying. If you buy one used or from a marketplace seller, check its date code against the 2022 rear-guard recall first.
Good fit
Get it if
- You crosscut wide boards.
- You want a shadow cutline and mostly work indoors.
- You bevel both ways.
- You want a wide miter range with positive stops.
Look elsewhere
Skip it if
- You care most about dust collection. It’s owners’ most common complaint (see What owners don’t like).
- You’re short on bench depth. The rails need room behind the saw (see the bench-depth answer in the FAQ).
- You don’t need the shadow line. The DWS779 is the same saw without it (see the alternatives below).
- Your boards are 2x8 or narrower. A non-sliding saw will do (see the alternatives below).
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.
Safety recall: check the date code (CPSC 22-196)
What: In August 2022 DeWalt recalled DWS779, DWS780 and DHS790 miter saws because the rear guard can break or detach. CPSC lists 571 reports, including 9 lacerations, and about 1.25 million saws sold in the US from April 2019 to May 2022, including on Amazon.com (CPSC recall 22-196, Aug 4, 2022).
Which saws: sources differ. The CPSC notice and DeWalt’s own recall notice cover date codes 2019 04 through 2022 04. DeWalt’s support article on the recall (updated Mar 13, 2026) says 2019 04 through 2022 03. Don’t rely on either end date alone: check your date code on the official recall page (dewalt.com/miter-saw-recall, the page CPSC links), or call DeWalt at 800-990-6421.
Where the date code is: CPSC says on the black plastic motor end cap, next to the nameplate. DeWalt’s support article says on the label on top of the motor, and asks you to contact DeWalt if your saw has no date code or you can’t find it. Saws with a green dot on the nameplate or a black dot on the arm aren’t included (CPSC).
If yours is included: Stop using it. The remedy is a free repair kit, or a free repair at a DeWalt service center (CPSC). Owners report waits: comments on DeWalt’s support article from Sep 2022 to Jun 2023 ask about kits that hadn’t arrived. One owner on X said the repaired part failed again and injured his hand (@iamjeff_ups, Mar 15, 2024).
Buying used: Check the date code and the dots before you buy.
Usage info: our math
DeWalt lists 7-1/2 in crown nested and 6-3/4 in base held vertically against the fence (product page, checked Oct 23, 2026). For board width, the manual’s table is more exact than DeWalt’s nominal ratings in the checker below:
| Miter | Board height | Widest cut |
|---|---|---|
| 0° | 3.0 in | 13.75 in |
| 0° | 4.4 in | 9.1 in |
| 45° | 3.0 in | 9.6 in |
Source: DWS780 instruction manual N466020 (Type 20).
Static check: DeWalt rates the DWS780 to 2x14 at 90° and 2x10 at 45°.
Key specs
| Motor | 15 A, 3,800 rpm; 1,600 W input (manual) |
| Blade | 12 in. 1 in arbor; 5/8 in arbor blades fit with the included adapter (DeWalt part 152636-00). Blades must be rated for at least 4,800 rpm. |
| Miter | 60° right, 50° left, 10 positive stops |
| Bevel | 49° left and right (manual) |
| Cutline | XPS LED shadow line |
| Dust | Bag included; DeWalt claims over 75% capture |
| Weight | 56 lb (DeWalt product page data; not in the manual) |
| In the box | Saw, 12 in carbide blade, blade wrench, dust bag, vertical material clamp. No stand. |
Sources: DeWalt’s DWS780 product page (checked Oct 23, 2026), the Type 20 manual N466020, and DeWalt’s arbor FAQ (updated Jan 5, 2023). The weight is the “Assembled Product Weight” in the product page’s data; a video reviewer also says about 56 lb (ToolMetrix, YouTube).
How we counted owner reviews
We read 76 Amazon reviews of this listing (checked Oct 23, 2026) and counted 63. We left out 2 reviews of the reconditioned DWS780R, 1 that may be about a different saw, and 10 from 2012–2013 that may describe an earlier version. This sample leans critical. Amazon shows about 10 reviews per filter, and we read deeper into the critical ones: 40 of the 63 come from Amazon’s lower rating tiers, though most of this saw’s Amazon ratings are in the top tiers. The 23 positive reviews are a sample, mostly recent. So a count shows what owners raise, not how often saws fail. One review can count under several headings, and we read the opening of each review, not always the full text. Reports from outside Amazon are labeled and not added to the counts.
What owners like best
Accurate, square cuts
6 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Owners say it cut straight and square out of the box. Outside Amazon, an owner of a few years found the fences square from the factory, the table flat, and rail play under 1/64 in (Doresoom Tool Reviews, YouTube, Jan 11, 2025).
The XPS shadow cutline
4 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Owners like seeing the blade’s shadow on the pencil mark with nothing to calibrate. One catch from a video review: the shadow is hard to see in bright sun (ToolMetrix, YouTube).
Solid build
3 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Described as sturdy and well built.
Arrived intact and complete
2 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Worth noting given the shipping complaints below.
Also: 7 reviews that raised a complaint still called it a good or great saw, and 4 more praised it without giving a reason. With only 23 positive reviews in the sample, treat these as examples, not proportions.
What owners don’t like
Weak dust collection, or the port won’t take a vacuum hose
9 of 63 reviews we checked (Amazon, checked Oct 23, 2026); 12 with the port problems below
The most common complaint: hoses don’t seat on the port, and dust ends up everywhere despite DeWalt’s capture claim in Key specs. A long-time owner called it one of the worst for dust collection (Doresoom Tool Reviews, YouTube).
Fix: Plan on an adapter between the port and your hose; one video reviewer used duct tape or a plumbing coupling (ToolMetrix, YouTube). We don’t have an official DeWalt adapter model for this port.
Avoid or spot it: Check your hose end before the saw arrives, and clear the dust duct now and then (see Maintenance).
Dust port or duct gets in the way, or cracks
3 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
The port hit the angle gauge and made the saw stick; the blade safety catch hit a port rivet; a cracked duct blocked the slide.
Fix: A cracked port is a service part: N142121 on DeWalt ServiceNet. Part numbers depend on your saw’s Type (on the nameplate); check yours on ServiceNet.
Avoid or spot it: On day one, swing the saw through its full miter and slide range and listen for rubbing.
XPS light dies
5 of 63 reviews we checked (Amazon, checked Oct 23, 2026); 2 more found it weak
The LED stopped working, from first use to under two years in, and owners struggled to get a replacement. One X user reported the same in 2018 (@AdamKyle83).
Fix: Warranty claim. DeWalt ServiceNet lists the XPS “LED & Power Supply Kit” as N515802; quote it when you call. Part numbers depend on your saw’s Type (on the nameplate); check yours on ServiceNet.
Avoid or spot it: Test the light on its own switch when the saw arrives, and again before the 90-day guarantee ends.
Blade, blade bolt or guard hardware
5 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
A blade bolt that stripped with the supplied wrench, a guard missing a nut, a lost safety-catch spring, a blade missing a tooth, and one reviewer whose blade broke and jammed, with a bent spring and a near eye injury.
Fix: Don’t run a saw with a damaged guard; the manual says to check guards and parts for damage before use. Get it repaired or replaced under warranty.
Avoid or spot it: Before the first cut, check that the guard moves freely and returns, every fastener is there, and the blade is intact.
Arrived damaged, opened or repacked
4 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Torn or different packaging; in one review, a broken saw.
Fix: Return or replace it through Amazon.
Avoid or spot it: Unbox right away and inspect the base, rails, fences and guard.
Blade hits the kerf plate, or cuts aren’t precise
4 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Two say the blade hit the kerf plate (one at 45° bevel), one says the insert wasn’t flush, and one says cuts weren’t repeatable. Outside Amazon, one owner found the blade touching a small plastic part out of the box (Ben Finio, YouTube), and one on X got a bent fence (@AmmonKerns, Jun 2022).
Fix: The manual’s kerf plate adjustment: loosen the screws and set the plates as close as possible without touching the blade. It also covers miter scale, bevel square and 45° bevel stop adjustments. If it still won’t hold, use the 90-day guarantee.
Avoid or spot it: Unplugged, lower the blade slowly at 0° and both 45° bevels, then make a test cut and check it with a square. You may need your own T20 driver for the small pointer screws (Projects For All, YouTube, borrowed unit).
Motor died, tripped the breaker, or grinding
3 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
One saw stopped a quarter turn into its first cut, one tripped the breaker and died, one leaked grease and ground after little use.
Fix: Warranty claim. If it only trips the breaker, the manual’s troubleshooting points to the circuit; one owner tripped his cutting 6x6s too aggressively (Ben Finio, YouTube).
Avoid or spot it: Run it on your usual circuit within the return window. The manual says a too-light or too-long extension cord can stop the blade reaching speed.
Not worth it over another DeWalt
4 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Reviewers felt it wasn’t enough better than the DWS779 or other DeWalt saws.
Fix: Not a defect. See the alternatives below.
Avoid or spot it: Decide whether you’ll use the shadow line.
Loud, runs hot, or kicks at start-up
3 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
One found it very loud, one said it overheats in long continuous use, one was surprised by the torque kick.
Fix: Not defects. Keep a firm grip at start-up, and let the motor reach full speed before cutting (manual).
Avoid or spot it: If you cut all day, plan breaks.
60-tooth blade where the listing said 80
2 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
The blade in the box had 60 teeth.
Fix: Not a defect: DeWalt’s page says only “12 in carbide blade”.
Avoid or spot it: Count the teeth if it matters for trim, and plan for a finer blade (see What else you’ll need).
Big and heavy
2 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Reviewers found it large and heavy to move.
Fix: Not a defect.
Avoid or spot it: Check the weight in Key specs and the bench depth in the FAQ before you buy.
Wrong or missing parts
2 of 63 reviews we checked (Amazon, checked Oct 23, 2026)
Wrong table extensions in one box; missing side handles in another.
Fix: Contact Amazon or the seller for a replacement or return.
Avoid or spot it: Check the box contents against the list in Key specs on arrival.
Support and warranty trouble is covered under Warranty and claims. 3 more reviewers made general quality complaints without specifics, and 1 warned other buyers about the recall.
Warranty and claims
Length: 3-year limited warranty, 1-year free service contract and a 90-day money-back period (dewalt.com warranty page, read Oct 21, 2026). It covers the original end user only.
Who’s covered: DeWalt says the warranty applies only to tools bought from DeWalt or a DeWalt authorized seller, and it may reject claims for tools bought from unauthorized sellers, including unauthorized websites. DeWalt doesn’t name Amazon.com either way. If you’re unsure about a seller, DeWalt says to ask internetadmin@sbdinc.com.
Registration: not required, and nothing on DeWalt’s warranty page says it extends the term.
Not covered: normal wear, abuse, accessories, and repairs someone else attempted.
How to claim: 1) Find your receipt. DeWalt says proof of purchase showing when and where you bought it may be required, and a receipt is required for the 90-day refund. 2) Use DeWalt’s web request form at support.dewalt.com (DeWalt calls it the fastest route), call 1-800-433-9258, or take the tool to a DeWalt service center (dewalt.com/service-center). 3) Don’t open the tool yourself first; repairs by others are excluded.
Owner experience: 7 of 63 reviews we checked (Amazon, checked Oct 23, 2026) describe support or warranty trouble: an unhelpful rep, a runaround over a grinding motor, a far-off service center, and XPS parts DeWalt wouldn’t or couldn’t supply. An X user with a bent fence was sent to a service center over an hour away (@AmmonKerns, Jun 2022). Before you buy, check how far your nearest DeWalt service center is.
Is it better than the alternatives?
Our verdict: the DWS780 is the better buy only if you need wide crosscuts and will use the shadow line. If not, one of the saws below does the same job for less bench space or the same capacity without the light, the part owners most often say failed. We haven’t tallied Amazon reviews of the rivals, so these calls rest on DeWalt’s specs plus what DWS780 owners report.
vs DeWalt DWS779 (same saw, no XPS light)
DeWalt lists the same motor, blade, cut capacities and warranty; the DWS780 adds the XPS cutline. DWS780 owners split on the light: in the reviews we checked, more say it died or was weak than praise it, and 2 told buyers to get the DWS779 instead. Pick the DWS780 if you work indoors and will use the shadow line. Pick the DWS779 if you mark by eye or work in bright sun. Specs side by side: DeWalt DWS779 vs DWS780.
vs DeWalt DWS716 or DWS715 (12 in, non-sliding)
No rails, so they need far less bench depth, but they cut much narrower boards: the DWS716 manual lists 7.9 in wide at 0°. The DWS716 bevels both ways; the DWS715 bevels left only. Our owner data for those two is thin (3 forum threads in total), so we can’t say which holds up better. Pick a non-slider if your boards are 2x8 or narrower and space is tight. Pick the DWS780 for anything wider. Guides: DWS716 and DWS715; specs side by side: DeWalt DWS715 vs DWS716.
Maintenance and care
From DeWalt’s DWS780 manual (N693246):
- Blow dust out of the vents with dry air at least once a week.
- Clean non-metallic parts only with a cloth dampened with water and mild soap. Never use lubricants or cleaners near the polycarbonate guard.
- Clean dust from around and under the base and rotary table now and then.
- Clear the dust duct with low-pressure air or a large dowel, with the saw unplugged and the head fully raised.
- Clean the worklight lens with a cotton swab, no solvents. Clean pitch off the blade.
- Bearings are sealed and lubricated for life.
- The belt is designed to last the tool’s life; don’t overtighten it when adjusting tension.
- Brushes: take the saw to a service center.
The newer Type 20 manual (N466020) adds: replace the kerf plate when it’s damaged.
What else you’ll need
Accessory listings weren’t matched to Amazon products in our checks, so we give DeWalt’s part numbers instead of guessing a link.
12 in finer-tooth blade
Why: A higher tooth count than the stock blade cuts cleaner trim.
Who can skip it: If the stock blade is clean enough for your work.
Is it good? Not tallied.
Official or third-party: Either.
Will it fit? Yes if it meets the blade rules in Key specs (size, arbor, rpm rating).
No specific blade listing chosen.
DW7082 clamp
Why: Holds work to the fence or table for repeat or small cuts.
Who can skip it: If you hand-hold only long stock.
Is it good? Not tallied.
Official or third-party: Official DeWalt.
Will it fit? Yes: named in the DWS780 manual.
Amazon listing not confirmed yet; search DW7082.
DW7080 extension
Why: Supports long boards past the base.
Who can skip it: Short-stock work.
Is it good? Not tallied.
Official or third-party: Official DeWalt.
Will it fit? Yes: named in the DWS780 manual.
Amazon listing not confirmed yet; search DW7080.
DW7084 crown molding fence
Why: Holds crown nested against the fence for cutting.
Who can skip it: If you don’t cut crown.
Is it good? Not tallied.
Official or third-party: Official DeWalt.
Will it fit? Yes: named in the DWS780 manual.
Amazon listing not confirmed yet; search DW7084.
Replacement parts owners ask about
Why: Fence parts, if one arrives bent or damaged.
Who can skip it: Until something breaks.
Is it good? Not tallied.
Official or third-party: Official DeWalt service parts.
Will it fit? Fences: right N081818SV, left N081824SV, “Fence” N597938 (DeWalt ServiceNet (toolservicenet.com), checked Oct 22, 2026). The dust port and XPS light part numbers are with those complaints under What owners don’t like. Part numbers depend on your saw’s Type (on the nameplate); check yours on ServiceNet.
Order through DeWalt service, not Amazon.
DW7053 dust bag
Why: Replacement for the included bag.
Who can skip it: If you run a vacuum.
Is it good? Not tallied.
Official or third-party: Official DeWalt.
Will it fit? Yes: named in the DWS780 manual (N466020).
Amazon listing not confirmed yet; search DW7053.
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.
FAQ
Will it cut a 4x4 or a 6x6?
A 4x4 (3.5 in), yes: it fits under the 4.4 in height in the manual’s table. A 6x6 won’t go through in one pass; one owner said about 1/4 to 1/2 in was left (Ben Finio, YouTube, Oct 3, 2025).
What is XPS, and is it a laser?
It isn’t a laser. XPS is an LED that casts the blade’s shadow onto the work as a cutline, on its own switch (manual).
How much bench depth does it need?
DeWalt doesn’t publish it. One owner measured about 52 in front to back with the dust bag, or about 42 in with a 90° hose connector instead (Doresoom Tool Reviews, YouTube, Jan 11, 2025).
Does it have a soft start?
No, per an owner’s video review, which notes a small upward kick at start-up (Doresoom Tool Reviews). DeWalt’s page and manual don’t list one.
Can it cut metal?
Not steel or iron: the manual says never to cut ferrous metals. It lists a blade type for non-ferrous metals.
Could I get a reconditioned saw from this listing?
Some reviews on this listing are for the reconditioned DWS780R; one says it wasn’t disclosed and the warranty was refused. Check that the listing and the box say new DWS780 before you order.
Sources
- DeWalt DWS780 product page, dewalt.com: specs, box contents and product data (checked Oct 23, 2026)
- DeWalt DWS780 instruction manual N466020, Type 20 (assets.dewalt.com), read Oct 23, 2026
- DeWalt DWS780 instruction manual N693246 (care steps), read Oct 22, 2026
- DeWalt support FAQ on the DWS780 arbor size (updated Jan 5, 2023), checked Oct 23, 2026
- CPSC recall 22-196, DeWalt miter saws (Aug 4, 2022), checked Oct 23, 2026
- DeWalt’s miter saw recall notice, and DeWalt support’s recall article (updated Mar 13, 2026) with owner comments, checked Oct 23, 2026
- DeWalt warranty page, dewalt.com/en-us/support/warranty (read Oct 21, 2026)
- DeWalt ServiceNet parts list for the DWS780 (toolservicenet.com), checked Oct 22, 2026
- Amazon reviews of listing B00540JS7C: 76 read, 63 counted (checked Oct 23, 2026)
- Owner videos on YouTube: Doresoom Tool Reviews (Jan 11, 2025), Ben Finio (Oct 3, 2025), ToolMetrix, Projects For All (borrowed unit)
- Owner posts on X: @AmmonKerns (Jun 2022), @AdamKyle83 (Jan 2018), @iamjeff_ups (Mar 2024)
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.