Side-by-side specs are on the comparison pages below.
Full specs side by side: DeWalt DWE7485 vs SKIL TS6307-00
Jobsite table saws · Single-tool guide
Quick verdict
The TS6307-00 gives you a 10 in blade, a 25-1/2 in right rip and a folding stand. The most important thing to know is the warranty: 1 year, or 3 years if you register within 30 days. Both owner threads our search found were about the rip fence slipping, and the manual has the rail-lock and fence steps to fix it, so set them on day one.
Good fit
Look elsewhere
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.
From the manual (p14–15): depth 3-1/2 in at 90° and 2-1/2 in at 45°; rip 25-1/2 in right and 14 in left; bevel -2° to 47° with stops at 0 and 45°. SKIL lists a 24 x 25 in table and a 32 in table height on the stand. Use it on wood and wood composites only; the manual says not to cut metal or plastics.
What that means (our math from the official figures, not a maker claim): 2x stock (1.5 in) cuts in one pass at 90° and 45°. A 4x4 (3.5 in actual) equals the 90° max depth, so there’s no margin.
Static check: the TS6307-00 rips up to 25.5 in to the right of the blade.
Owner threads here come from web-search result snippets on Oct 22, 2026; Reddit blocked direct reads, so we didn’t open the threads in full. Small sample: a count means “this many of the threads that search returned”, not a failure rate. We didn’t check Amazon reviews for this tool.
Reported in 2 of 2 TS6307-identified owner threads our Oct 22, 2026 search returned (Reddit r/BeginnerWoodWorking and r/woodworking; search snippets, small sample)
Owners say the fence won’t stay put after locking. In one thread, a commenter found the front pinion loose on the transfer rod (over 1/8 in front-to-back shift); another fixed it by tightening the screw inside the drive knob.
Fix: Set the rail-lock tension (M6 jam nut and hex rod underneath), then align the fence posts (manual p26–27, under Maintenance and care below).
Avoid or spot it: Lock the fence, push on it front and back, and measure to the blade at both ends before the first cut.
Reported in 2 of 4 owner threads our Oct 21, 2026 search returned, likely the same owner (Reddit; search snippets, small sample)
One owner posted in two places; SKIL’s replacement table had the same issue. A watch item, not a confirmed pattern.
Fix: Warranty claim through SKIL.
Avoid or spot it: Check flatness with a straightedge on arrival.
Length: 1 year for SKIL benchtop tools, or 3 years if you register at registermyskil.com within 30 days of purchase (you need the receipt to register). 90 days for professional or commercial use. (skil.com warranty page, last updated 11/21/2025.)
Who’s covered: the original purchaser from an authorized SKIL retailer; Chervon may reject claims from unauthorized sellers.
Not covered: blades and belts (consumables).
How to claim: 1) Call 1-877-754-5999 with a description of the defect and your original dated receipt. 2) Return the complete tool to a SKIL Factory Service Center or Authorized Service Station; you pay shipping.
Note: SKIL’s page doesn’t name the TS6307-00 under “Benchtop Tools”, but the manual’s warranty is titled for SKIL consumer bench top power tools.
From SKIL TS6307-00 manual (checked Oct 22, 2026). Page numbers are PDF pages. Unplug the saw before any adjustment.
Not linked yet: we haven’t verified retail listings for these parts.
Why: Required for dado cuts.
Who can skip it: If you won’t cut dados.
Is it good? Not tallied.
Official or third-party: Official SKIL.
Will it fit? Stacked dado sets only, 8 in diameter, up to 5/8 in wide, at 0° only; no wobble dados (manual p43–45). The insert’s combination nut/washer replaces the outer washer.
Not linked yet.
Why: Cleaner cuts and less tear-out.
Who can skip it: If you mostly bevel.
Is it good? Not tallied.
Official or third-party: Official SKIL.
Will it fit? For the TS6307 only, 90° cuts only, no bevels (STZ6307 manual). You drill four 1/8–9/64 in holes in the insert supports and fit #8x3/8 in screws, with the riving knife at its lowest.
Not linked yet.
Why: Replacement or finer cut.
Who can skip it: Until the stock 24T blade dulls.
Is it good? Not tallied.
Official or third-party: Either.
Will it fit? 10 in (254 mm), 5/8 in arbor, rated above 4,600 rpm. Kerf 0.1 in or wider and plate 0.071 in or thinner to suit the .090 in riving knife; no extra-thin-kerf blades (manual p15, p20–21).
No listing: blade part numbers aren’t verified yet.
Why: Dust collection.
Who can skip it: If you use the dust elbow alone.
Is it good? Not tallied.
Official or third-party: Either.
Will it fit? The port takes a 2-1/2 in outside-diameter hose; other sizes need an adapter (manual p14, p49).
No listing.
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.
Side-by-side specs are on the comparison pages below.
Full specs side by side: DeWalt DWE7485 vs SKIL TS6307-00
Register at registermyskil.com within 30 days; you’ll need the receipt.
Blades and belts.
5/8 in max, with an 8 in stacked set and the STA6307 insert, at 0° only.
Yes, SKIL’s STZ6307, for 90° cuts only.
Only just: the 3-1/2 in max depth equals a 4x4’s actual thickness (our math).
Owners report it; the manual’s fix is the rail-lock tension adjustment, then fence post alignment (p26–27).
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.