Side-by-side specs are on the comparison pages below.
Full specs side by side: DeWalt DW734 vs DW735 planer
Benchtop thickness planers · Single-tool guide
Quick verdict
The DW735 is a 13 in, two-speed lunchbox planer with fan-assisted chip ejection. It’s the one to get if you mill rough or reclaimed boards often and have a real dust collector. Plan around two things: DeWalt says a shop vac can’t keep up with it, and the most-reported owner fault is the feed rollers stopping while the cutterhead spins, which is usually a small drive part, not the motor.
Good fit
Look elsewhere
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.
DeWalt’s manual caps a pass at 1/8 in on boards 6 in wide or narrower (its spec table says 0.13 in, which agrees). It doesn’t give a figure for wider boards, so take shallower passes there. Max thickness is 6 in, minimum 1/8 in, and DeWalt advises against stock narrower than 3/4 in.
At 96 cuts per inch you get 1,152 knife marks per foot; at 179 it’s 2,148, nearly twice as fine, which is why the slow speed is for finish passes.
Example: taking a 1 in board to 3/4 in removes 1/4 in, so at least 2 passes at DeWalt’s 1/8 in max on boards up to 6 in wide.
Owner threads were found with one problem-targeted web search per tool on Oct 21, 2026, so a count means “this many of the threads that search returned”, not a failure rate. We couldn’t read Amazon’s critical reviews in that check, so there’s no Amazon review count; where we mention Amazon’s “Customers say” box, that’s Amazon’s own summary, not a tally.
Reported in 3 of 4 owner threads we checked (Reddit r/woodworking, WoodTalk Online and Sawmill Creek, checked Oct 21, 2026)
Owners describe boards that stop feeding even though the knives are still running. The cause in these threads was a sheared sprocket key or sprocket, or a seized roller. Amazon’s “Customers say” summary also mentions broken drive sprockets.
Fix: DeWalt’s support article says to make sure the speed lever is fully in position 1 or 2 and to change speed only with the planer running. If it still won’t feed, DeWalt says to go to a service center, which keeps the warranty intact.
Avoid or spot it: Never shift speeds with the motor off or the lever half-way. If feeding stops after a jam, suspect the sprocket key before anything else.
Reported in 1 of 4 owner threads we checked (Reddit r/woodworking, checked Oct 21, 2026)
A deeper cut on the first or last few inches. One thread, so not a pattern by our count.
Fix: The manual’s snipe section says to keep the board level and supported as it enters and leaves.
Avoid or spot it: Support long boards with infeed and outfeed tables or stands, and leave extra length you can trim off.
Length: 3-year limited warranty, 1-year free service contract and a 90-day money-back period (dewalt.com warranty page, read Oct 21, 2026). It covers the original end user only.
Who’s covered: DeWalt says the warranty applies only to tools bought from DeWalt or a DeWalt authorized seller, and it may reject claims for tools bought from unauthorized sellers, including unauthorized websites. DeWalt doesn’t name Amazon.com either way. If you’re unsure about a seller, DeWalt says to ask internetadmin@sbdinc.com.
Registration: not required, and nothing on DeWalt’s warranty page says it extends the term.
Not covered: normal wear, abuse, accessories, and repairs someone else attempted.
How to claim: 1) Find your receipt. DeWalt says proof of purchase showing when and where you bought it may be required, and a receipt is required for the 90-day refund. 2) Use DeWalt’s web request form at support.dewalt.com (DeWalt calls it the fastest route), call 1-800-433-9258, or take the tool to a DeWalt service center (dewalt.com/service-center). 3) Don’t open the tool yourself first; repairs by others are excluded.
Rechecked: DeWalt’s USA/CAN warranty article (May 2026) gives the same 3-year limited, 1-year free service and 90-day terms, for tools bought from DeWalt or an authorized seller (support.dewalt.com, checked Oct 29, 2026).
Kit version (partly verified): DeWalt also sells the DW735X, the same planer with tables and extra knives.
From DeWalt’s DW735 manual (N486408):
Accessory listings weren’t matched to an Amazon product in our Oct 21 check unless a link is shown, so we name the part number instead of guessing a link.
Why: The knives are disposable and reversible, so when both edges are dull you replace the set.
Who can skip it: Anyone still on the first set of edges.
Is it good? Not tallied; no owner count yet.
Official or third-party: Official DeWalt, listed in the DW735 manual.
Will it fit? Yes for the DW735 (13 in). It won’t fit the DW734, which uses 12-1/2 in knives.
Amazon listing not confirmed yet; search the part number DW7352.
Why: Extra support on long boards, which is DeWalt’s main snipe advice.
Who can skip it: If you already have your own infeed and outfeed support.
Is it good? Not tallied.
Official or third-party: Official DeWalt (manual).
Will it fit? Made for the DW735 per the manual.
Amazon listing not confirmed yet.
Why: Puts a heavy planer on wheels.
Who can skip it: If it lives on a bench.
Is it good? Not tallied.
Official or third-party: Official DeWalt (manual).
Will it fit? Listed in the DW735 manual.
Amazon listing not confirmed yet.
Why: Part of DeWalt’s chip-collection setup for the fan ejection.
Who can skip it: If your collector hose already connects.
Is it good? Not tallied.
Official or third-party: Official DeWalt (manual).
Will it fit? Listed in the DW735 manual.
Amazon listing not confirmed yet.
Why: Owners search for them for a quieter, smoother cut.
Who can skip it: Everyone, per DeWalt.
Is it good? Not tallied.
Official or third-party: Third-party.
Will it fit? Not recommended by DeWalt. The manual says helical cutterheads haven’t been tested with this planer.
No link.
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.
Side-by-side specs are on the comparison pages below.
Full specs side by side: DeWalt DW734 vs DW735 planer
DeWalt’s manual says no: a shop vac can’t keep up and the hose clogs. Use a dust collector.
DeWalt says helical cutterheads haven’t been tested with it and aren’t recommended.
1/8 in on boards 6 in wide or less, per DeWalt. Go shallower on wider boards.
In the owner threads we read, it was usually a sheared sprocket key or sprocket. Check the speed lever is fully engaged, then see a DeWalt service center.
DeWalt’s DW735X kit is the same planer with tables and extra knives.
As an Amazon Associate I earn from qualifying purchases. Links on this page are Amazon affiliate links; buying through them doesn’t change what you pay.