Quick verdict
The Makita RT0701C is a corded compact router with a 1-1/4 HP maximum motor, a 6.5 AMP draw, electronic constant speed from 10,000 to 30,000 RPM, soft start, and a 3.9 lb weight on Makita’s official US page. [Source: Makita RT0701C] It ships with a trimmer base, a 1/4 in collet, a straight guide, and two wrenches. This guide walks through the official setup and cut steps from the instruction manual. The Bosch Colt appears only as the other model on the existing Colt vs Makita palm router comparison; this page does not recommend it. Not tested hands-on.
What you get, and what you add later
The official US Includes list is Trimmer Base 196613-4, 1/4 in Collet 763637-1, Straight Guide 122965-7, and wrenches 781039-9 and 781011-1. The tool uses 1/4 in shank bits, has a rack-and-pinion depth adjustment, a cam lock, a shaft lock, and is double insulated. Length is listed as 7-7/8 in. [Source: Makita RT0701C]
The instruction manual lists collet chuck capacity of 1/4 in and 3/8 in. If you need a 3/8 in collet, Makita sells official collet 763619-3 for the RT0700C and RT0701C. Dust nozzle sets are optional accessories in the manual; the official fixed-base dust extracting attachment is 195559-1. [Source: RT0701C manual]
Set the speed before you cut
Turn the speed-adjusting dial to a number from 1 to 6. Higher numbers raise speed; 6 is the high end and 1 is the low end. The official manual gives these approximate no-load speeds and warns you not to force the dial past its stops. Running continuously at low speed for a long time can overload the motor.
| Dial setting | Approximate no-load speed (min⁻¹) |
|---|---|
| 1 | 10,000 |
| 2 | 12,000 |
| 3 | 17,000 |
| 4 | 22,000 |
| 5 | 27,000 |
| 6 | 30,000 |
The electronic constant-speed control is meant to hold speed under load for a finer finish, and soft start is listed as a standard feature. Pick a speed that matches the material and the bit diameter, as the manual states, rather than leaving the dial on 6 for every cut. [Source: RT0701C manual]
Official setup steps
- Disconnect the tool before you change a bit.
- Insert the bit all the way into the collet cone. Tighten the collet nut with the two wrenches, or press the shaft lock and use the provided wrench. To remove a bit, reverse the same steps.
- Do not tighten the collet nut without a bit in place. The manual says the collet cone will break if you do.
- Set bit protrusion by loosening the locking lever and the adjusting screw. After you set the depth, tighten the locking lever. If the base still moves, tighten the hex nut and then tighten the locking lever again.
- Place the base on the workpiece with the bit not touching the wood. Start the tool and wait until the bit reaches full speed, then feed the cut. Do not start with the bit already buried in the work.
- For grooves, each pass should not be more than 3 mm (1/8 in) deep. Make several passes if you need a deeper groove.
Optional bases, with official limits
These official accessories fit the RT0701C (and, as each page states, the related compact models). They are sold separately.
- Plunge Base 196094-2. Official plunge capacity is 0 in. to 1-3/8 in. [Source: Makita 196094-2]
- Tilt Base 198987-9. Official positive stops at −30 degrees and 45 degrees. Makita describes it for trimming laminated boards and other thin materials. [Source: Makita 198987-9]
- Offset Base 195562-2. Official claim: routing as close as 3/4 in to a wall, for countertops and kitchen or bathroom sink cut-outs, with 1/4 in shank bits. This is an offset base, not a tilt base. [Source: Makita 195562-2]
If you add a dust nozzle, fit it so the protrusion matches the notch in the tool and connect a vacuum, as the manual shows. The dust parts are optional, not in the standard box.
Warranty on this corded model
Makita’s official US warranty page gives a 3-year limited warranty to lithium-ion tools, batteries and chargers, MAKTRAK, and pneumatic nailers. The RT0701C is a corded tool, so it falls under the general product limited warranty: one year from the original purchase, with the complete product returned to a Factory or Authorized Service Center. The instruction manual prints the same one-year limited warranty. [Source: Makita warranty]
As an Amazon Associate I earn from qualifying purchases. There are no prices on this page.
Questions buyers actually ask
What collet comes with the RT0701C?
The official US product page includes a 1/4 in collet (763637-1) and says the tool uses 1/4 in shank bits. The manual lists collet capacity of 1/4 in and 3/8 in. The official 3/8 in collet 763619-3 is sold separately.
Is the RT0701C covered by Makita’s 3-year lithium-ion warranty?
No. Makita’s official warranty page reserves the 3-year limited warranty for lithium-ion tools, batteries, chargers, MAKTRAK, and pneumatic nailers. The corded RT0701C is under the general product limited warranty of one year from original purchase.
How deep can I cut in one pass?
The official manual says a groove should not be more than 3 mm (1/8 in) at a pass. For deeper grooves, make several passes.
How close can the offset base get to a wall?
Makita’s official 195562-2 page says as close as 3/4 in to a wall, and describes it for countertops and sink cut-outs with 1/4 in shank bits.